椰子殼-Blog

HP-UNIX DEFINITIONS ::= BEGIN

--
--  Hewlett-Packard definitons for unix agents
--  @(#) hp-unix $Date: 1998/07/30 18:52 UTC $ $Revision: /main/PULSAR/1 $
--

IMPORTS
        enterprises, NetworkAddress, IpAddress, Counter, Gauge,
  TimeTicks
            FROM RFC1155-SMI
 OBJECT-TYPE    
     FROM RFC-1212
 DisplayString    
     FROM RFC1213-MIB;

hp   OBJECT IDENTIFIER ::= { enterprises 11 }
nm  OBJECT IDENTIFIER ::= { hp 2 }
system  OBJECT IDENTIFIER ::= { nm 3 }
interface OBJECT IDENTIFIER ::= { nm 4 }
icmp  OBJECT IDENTIFIER ::= { nm 7 }
snmp  OBJECT IDENTIFIER ::= { nm 13 }
openView OBJECT IDENTIFIER ::= { nm 17 }
general  OBJECT IDENTIFIER ::= { system 1 }
hpux  OBJECT IDENTIFIER ::= { system 2 }
hpsun  OBJECT IDENTIFIER ::= { system 10 }
sparc  OBJECT IDENTIFIER ::= { hpsun 1 }
computerSystem OBJECT IDENTIFIER ::= { general 1 }
fileSystem OBJECT IDENTIFIER ::= { general 2 }
processes OBJECT IDENTIFIER ::= { general 4 }
cluster  OBJECT IDENTIFIER ::= { general 5 }
ieee8023Mac OBJECT IDENTIFIER ::= { interface 1 }
trap  OBJECT IDENTIFIER ::= { snmp 1 }
snmpdConf OBJECT IDENTIFIER ::= { snmp 2 }
authfail OBJECT IDENTIFIER ::= { snmp 4 }
openViewTrapVars OBJECT IDENTIFIER ::= { openView 2 }

-- sysObjectId definitions.  These values are returned in the
--    .iso.org.dod.internet.mgmt.mib-2.system.sysObjectID.0 variable

hp386  OBJECT IDENTIFIER ::= { system 8 }
hp9000s300 OBJECT IDENTIFIER ::= { hpux 2 }
hp9000s800 OBJECT IDENTIFIER ::= { hpux 3 }
hp9000s700 OBJECT IDENTIFIER ::= { hpux 5 }
hpOpenView OBJECT IDENTIFIER ::= { openView 1 }
sun4  OBJECT IDENTIFIER ::= { sparc 1 }
sun5  OBJECT IDENTIFIER ::= { sparc 2 }

-- the ComputerSystem Group

computerSystemUpTime OBJECT-TYPE
 SYNTAX TimeTicks
 ACCESS read-only
 STATUS mandatory
 DESCRIPTION
  "Time since the last boot."
 ::= { computerSystem 1 }

computerSystemUsers OBJECT-TYPE
 SYNTAX  Gauge
 ACCESS read-only
 STATUS mandatory
 DESCRIPTION
  "Number of users logged on to system."
 ::= { computerSystem 2 }

computerSystemAvgJobs1 OBJECT-TYPE
 SYNTAX Gauge
 ACCESS  read-only
 STATUS mandatory
 DESCRIPTION
  "Average number of jobs in the last 1
  minute * 100."
 ::= { computerSystem 3 }

computerSystemAvgJobs5 OBJECT-TYPE
 SYNTAX  Gauge
 ACCESS  read-only
 STATUS mandatory
 DESCRIPTION
  "Average number of jobs in the last 5
  minutes * 100."
 ::= { computerSystem 4 }

computerSystemAvgJobs15 OBJECT-TYPE
 SYNTAX  Gauge
 ACCESS  read-only
 STATUS mandatory
 DESCRIPTION
  "Average number of jobs in the last 15
  minutes * 100."
 ::= { computerSystem 5 }

computerSystemMaxProc OBJECT-TYPE
 SYNTAX  INTEGER
 ACCESS  read-only
 STATUS mandatory
 DESCRIPTION
  "Maximum number of processes allowed in system.
   Implemented with Extensible SNMP Agent."
 ::= { computerSystem 6 }

computerSystemFreeMemory OBJECT-TYPE
 SYNTAX  Gauge
 ACCESS  read-only
 STATUS mandatory
 DESCRIPTION
  "Free memory.  SunOS - not implemented.
   Implemented with Extensible SNMP Agent."
 ::= { computerSystem 7 }

computerSystemPhysMemory OBJECT-TYPE
 SYNTAX  INTEGER
 ACCESS  read-only
 STATUS mandatory
 DESCRIPTION
  "Physical memory.  SunOS - not implemented.
   Implemented with Extensible SNMP Agent."
 ::= { computerSystem 8 }

computerSystemMaxUserMem OBJECT-TYPE
 SYNTAX  Gauge
 ACCESS  read-only
 STATUS mandatory
 DESCRIPTION
  "Maximum user memory.  SunOS - not implemented.
   Implemented with Extensible SNMP Agent."
 ::= { computerSystem 9 }

computerSystemSwapConfig OBJECT-TYPE
 SYNTAX  INTEGER
 ACCESS  read-only
 STATUS mandatory
 DESCRIPTION
  "Swap space configured.  SunOS - not implemented.
   Implemented with Extensible SNMP Agent."
 ::= { computerSystem 10 }

computerSystemEnabledSwap OBJECT-TYPE
 SYNTAX  Gauge
 ACCESS  read-only
 STATUS mandatory
 DESCRIPTION
  "Enabled via swapon.  SunOS - not implemented.
   Implemented with Extensible SNMP Agent."
 ::= { computerSystem 11 }

computerSystemFreeSwap OBJECT-TYPE
 SYNTAX  Gauge
 ACCESS  read-only
 STATUS mandatory
 DESCRIPTION
  "Currently free swap space.  SunOS - not implemented.
   Implemented with Extensible SNMP Agent."
 ::= { computerSystem 12 }

computerSystemUserCPU OBJECT-TYPE
 SYNTAX  Counter
 ACCESS  read-only
 STATUS mandatory
 DESCRIPTION
  "CPU used by users.  SunOS - not implemented.
   Implemented with Extensible SNMP Agent."
 ::= { computerSystem 13 }

computerSystemSysCPU OBJECT-TYPE
 SYNTAX  Counter
 ACCESS  read-only
 STATUS mandatory
 DESCRIPTION
  "CPU used by system.  SunOS - not implemented.
   Implemented with Extensible SNMP Agent."
 ::= { computerSystem 14 }

computerSystemIdleCPU OBJECT-TYPE
 SYNTAX  Counter
 ACCESS  read-only
 STATUS mandatory
 DESCRIPTION
  "CPU idle.  SunOS - not implemented.
   Implemented with Extensible SNMP Agent."
 ::= { computerSystem 15 }

computerSystemNiceCPU OBJECT-TYPE
 SYNTAX  Counter
 ACCESS  read-only
 STATUS mandatory
 DESCRIPTION
  "CPU nice.  SunOS - not implemented.
   Implemented with Extensible SNMP Agent."
 ::= { computerSystem 16 }

-- The FileSystem Group

fileSystemMounted OBJECT-TYPE
 SYNTAX  Gauge
 ACCESS  read-only
 STATUS mandatory
 DESCRIPTION
  "The number of file systems mounted."
 ::= { fileSystem 1 }

-- The FileSystem Table

fileSystemTable OBJECT-TYPE
 SYNTAX SEQUENCE OF FileSystemEntry
 ACCESS  not-accessible
 STATUS mandatory
 DESCRIPTION
  "File system table."
 ::= { fileSystem 2 }

fileSystemEntry OBJECT-TYPE
 SYNTAX FileSystemEntry
 ACCESS  not-accessible
 STATUS mandatory
 DESCRIPTION
  "Each entry contains objects for a particular file
  system."
 INDEX { fileSystemID1, fileSystemID2 }
 ::= { fileSystemTable 1 }

FileSystemEntry ::= SEQUENCE {
    fileSystemID1
 INTEGER,
    fileSystemID2
 INTEGER,
    fileSystemName
 DisplayString,
    fileSystemBlock
 INTEGER,
    fileSystemBfree
 INTEGER,
    fileSystemBavail
 INTEGER,
    fileSystemBsize
 INTEGER,
    fileSystemFiles
 INTEGER,
    fileSystemFfree
 INTEGER,
    fileSystemDir
 DisplayString
}

fileSystemID1 OBJECT-TYPE
 SYNTAX INTEGER (0..4294967295)
 ACCESS  read-only
 STATUS mandatory
 DESCRIPTION
  "First file system ID."
 ::= { fileSystemEntry 1 }

fileSystemID2 OBJECT-TYPE
 SYNTAX INTEGER (0..4294967295)
 ACCESS  read-only
 STATUS mandatory   
 DESCRIPTION
  "Second file system ID."
 ::= { fileSystemEntry 2 }

fileSystemName OBJECT-TYPE
 SYNTAX DisplayString
 ACCESS  read-only
 STATUS mandatory
 DESCRIPTION
  "Name of mounted file system."
 ::= { fileSystemEntry 3 }

fileSystemBlock OBJECT-TYPE
 SYNTAX INTEGER
 ACCESS  read-only
 STATUS mandatory
 DESCRIPTION
  "Total blocks in file system."
 ::= { fileSystemEntry 4 }

fileSystemBfree OBJECT-TYPE
 SYNTAX INTEGER
 ACCESS  read-only
 STATUS mandatory
 DESCRIPTION
  "Free blocks in file system."
 ::= { fileSystemEntry 5 }

fileSystemBavail OBJECT-TYPE
 SYNTAX INTEGER
 ACCESS  read-only
 STATUS mandatory
 DESCRIPTION
  "Free blocks avail to non-superuser."
 ::= { fileSystemEntry 6 }

fileSystemBsize OBJECT-TYPE
 SYNTAX INTEGER
 ACCESS  read-only
 STATUS mandatory
 DESCRIPTION
  "Fundamental file system block size."
 ::= { fileSystemEntry 7 }

fileSystemFiles OBJECT-TYPE
 SYNTAX INTEGER
 ACCESS  read-only
 STATUS mandatory
 DESCRIPTION
  "Total file nodes in file system."
 ::= { fileSystemEntry 8 }

fileSystemFfree OBJECT-TYPE
 SYNTAX INTEGER
 ACCESS  read-only
 STATUS mandatory
 DESCRIPTION
  "Free file nodes in file system."
 ::= { fileSystemEntry 9 }

fileSystemDir OBJECT-TYPE
 SYNTAX DisplayString
 ACCESS  read-only
 STATUS mandatory
 DESCRIPTION
  "File system path prefix."
 ::= { fileSystemEntry 10 }

-- The Processes Group

processNum OBJECT-TYPE
 SYNTAX  Gauge
 ACCESS  read-only
 STATUS mandatory
 DESCRIPTION
  "The number of processes running."
 ::= { processes 1 }

-- The processes table

processTable OBJECT-TYPE
 SYNTAX SEQUENCE OF ProcessEntry
 ACCESS  not-accessible
 STATUS mandatory
 DESCRIPTION
  "Processes Table.
   Implemented with Extensible SNMP Agent."
 ::= { processes 2 }

processEntry OBJECT-TYPE
 SYNTAX ProcessEntry
 ACCESS  not-accessible
 STATUS mandatory
 DESCRIPTION
  "Each entry contains information about a process
  running on the system."
 INDEX { processPID }
 ::= { processTable 1 }

ProcessEntry ::= SEQUENCE {
    processPID
 INTEGER,
    processIdx
 INTEGER,
    processUID
 INTEGER,
    processPPID
 INTEGER,
    processDsize
 Gauge,
    processTsize
 Gauge,
    processSsize
 Gauge,
    processNice
 Gauge,
    processMajor
 INTEGER,
    processMinor
 INTEGER,
    processPgrp
 INTEGER,
    processPrio
 INTEGER,
    processAddr
 INTEGER,
    processCPU
 Gauge,
    processUtime
 TimeTicks,
    processStime
 TimeTicks,
    processStart
 TimeTicks,
    processFlags
 INTEGER,
    processStatus
 INTEGER,
    processWchan
 INTEGER,
    processProcNum
 INTEGER,
    processCmd
 DisplayString,
    processTime
 INTEGER,
    processCPUticks
 Counter,
    processCPUticksTotal
 Counter,
    processFss
 INTEGER,
    processPctCPU
 Gauge,
    processRssize
 Gauge,
    processSUID
 INTEGER,
    processUname
 DisplayString,
    processTTY
 DisplayString
}

processPID OBJECT-TYPE
 SYNTAX INTEGER
 ACCESS read-only
 STATUS mandatory
 DESCRIPTION
  "The process ID (pid)."
 ::= { processEntry 1 }

processIdx OBJECT-TYPE
 SYNTAX INTEGER
 ACCESS read-only
 STATUS mandatory
 DESCRIPTION
  "Index for pstat() requests.  SunOS - not implemented."
 ::= { processEntry 2 }

processUID OBJECT-TYPE
 SYNTAX INTEGER
 ACCESS read-only
 STATUS mandatory
 DESCRIPTION
  "Process User ID."
 ::= { processEntry 3 }

processPPID OBJECT-TYPE
 SYNTAX INTEGER
 ACCESS read-only
 STATUS mandatory
 DESCRIPTION
  "Parent process ID."
 ::= { processEntry 4 }

processDsize OBJECT-TYPE
 SYNTAX Gauge
 ACCESS read-only
 STATUS mandatory
 DESCRIPTION
  "Process data size."
 ::= { processEntry 5 }

processTsize OBJECT-TYPE
 SYNTAX Gauge
 ACCESS read-only
 STATUS mandatory
 DESCRIPTION
  "Process text size."
 ::= { processEntry 6 }

processSsize OBJECT-TYPE
 SYNTAX Gauge
 ACCESS read-only
 STATUS mandatory
 DESCRIPTION
  "Process stack size."
 ::= { processEntry 7 }

processNice OBJECT-TYPE
 SYNTAX Gauge
 ACCESS read-only
 STATUS mandatory
 DESCRIPTION
  "Process nice value."
 ::= { processEntry 8 }

processMajor OBJECT-TYPE
 SYNTAX INTEGER
 ACCESS read-only
 STATUS mandatory
 DESCRIPTION
  "Process tty major number.  SunOS - not implemented."
 ::= { processEntry 9 }

processMinor OBJECT-TYPE
 SYNTAX INTEGER
 ACCESS read-only
 STATUS mandatory
 DESCRIPTION
  "Process tty minor number.  SunOS - not implemented."
 ::= { processEntry 10 }

processPgrp OBJECT-TYPE
 SYNTAX INTEGER
 ACCESS read-only
 STATUS mandatory
 DESCRIPTION
  "Process group of this process."
 ::= { processEntry 11 }

processPrio OBJECT-TYPE
 SYNTAX INTEGER
 ACCESS read-only
 STATUS mandatory
 DESCRIPTION
  "Process priority."
 ::= { processEntry 12 }

processAddr OBJECT-TYPE
 SYNTAX INTEGER
 ACCESS read-only
 STATUS mandatory
 DESCRIPTION
  "Address of process (in memory)."
 ::= { processEntry 13 }

processCPU OBJECT-TYPE
 SYNTAX Gauge
 ACCESS read-only
 STATUS mandatory
 DESCRIPTION
  "Processor utilization for scheduling."
 ::= { processEntry 14 }

processUtime OBJECT-TYPE
 SYNTAX TimeTicks
 ACCESS read-only
 STATUS mandatory
 DESCRIPTION
  "User time spent executing."
 ::= { processEntry 15 }

processStime OBJECT-TYPE
 SYNTAX TimeTicks
 ACCESS read-only
 STATUS mandatory
 DESCRIPTION
  "System time spent executing."
 ::= { processEntry 16 }

processStart OBJECT-TYPE
 SYNTAX TimeTicks
 ACCESS read-only
 STATUS mandatory
 DESCRIPTION
  "Time Process started."
 ::= { processEntry 17 }

processFlags OBJECT-TYPE
 SYNTAX INTEGER {
  incore(1),
  sys(2),
  locked(4),
  trace(8),
  trace2(16)
  }
 ACCESS read-only
 STATUS mandatory
 DESCRIPTION
  "Flags associated with process.  SunOS - values found in
  /usr/include/sys/proc.h."
 ::= { processEntry 18 }

processStatus OBJECT-TYPE
 SYNTAX INTEGER {
  sleep(1),
  run(2),
  stop(3),
  zombie(4),
  other(5),
  idle(6)
  }
 ACCESS read-only
 STATUS mandatory
 DESCRIPTION
  "The process status.  SunOS - sleep(1), wait(2), run(3),
  idle (4), zombie(5), stop(6)"
 ::= { processEntry 19 }

processWchan OBJECT-TYPE
 SYNTAX INTEGER
 ACCESS read-only
 STATUS mandatory
 DESCRIPTION
  "If processStatus is sleep, value sleeping on."
 ::= { processEntry 20 }

processProcNum OBJECT-TYPE
 SYNTAX INTEGER
 ACCESS read-only
 STATUS mandatory
 DESCRIPTION
  "Processor this process last run on.  SunOS - not
  implemented."
 ::= { processEntry 21 }

processCmd OBJECT-TYPE
 SYNTAX DisplayString
 ACCESS read-only
 STATUS mandatory
 DESCRIPTION
  "Command the process is running."
 ::= { processEntry 22 }

processTime OBJECT-TYPE
 SYNTAX INTEGER
 ACCESS read-only
 STATUS mandatory
 DESCRIPTION
  "Resident time for scheduling."
 ::= { processEntry 23 }

processCPUticks OBJECT-TYPE
 SYNTAX Counter
 ACCESS read-only
 STATUS mandatory
 DESCRIPTION
  "Ticks of cpu time."
 ::= { processEntry 24 }

processCPUticksTotal OBJECT-TYPE
 SYNTAX Counter
 ACCESS read-only
 STATUS mandatory
 DESCRIPTION
  "Total ticks for life of process.  SunOS - not
  implemented."
 ::= { processEntry 25 }

processFss OBJECT-TYPE
 SYNTAX INTEGER
 ACCESS read-only
 STATUS mandatory
 DESCRIPTION
  "Fair Share Schedular Group.  SunOS - not implemented."
 ::= { processEntry 26 }

processPctCPU OBJECT-TYPE
 SYNTAX Gauge
 ACCESS read-only
 STATUS mandatory
 DESCRIPTION
  "Percent CPU * 100 for this process."
 ::= { processEntry 27 }

processRssize OBJECT-TYPE
 SYNTAX Gauge
 ACCESS read-only
 STATUS mandatory
 DESCRIPTION
  "Resident Set Size for process (private pages)."
 ::= { processEntry 28 }

processSUID OBJECT-TYPE
 SYNTAX INTEGER
 ACCESS read-only
 STATUS mandatory
 DESCRIPTION
  "saved UID."
 ::= { processEntry 29 }

processUname OBJECT-TYPE
 SYNTAX DisplayString
 ACCESS read-only
 STATUS mandatory
 DESCRIPTION
  "User name."
 ::= { processEntry 30 }

processTTY OBJECT-TYPE
 SYNTAX DisplayString
 ACCESS read-only
 STATUS mandatory
 DESCRIPTION
  "Process TTY.  SunOS - not implemented."
 ::= { processEntry 31 }

-- The Ieee8023Mac Group
--  This group is not implemented on Solaris.

-- The Ieee8023Mac Table

ieee8023MacTable OBJECT-TYPE
 SYNTAX SEQUENCE OF Ieee8023MacEntry
 ACCESS  not-accessible
 STATUS mandatory
 DESCRIPTION
  "A list of IEEE 802.3 Interface entries."
 ::= { ieee8023Mac 1 }

ieee8023MacEntry OBJECT-TYPE
 SYNTAX Ieee8023MacEntry
 ACCESS  not-accessible
 STATUS mandatory
 DESCRIPTION
  "Each entry contains statistics for ieee 802.3
                interfaces."
 INDEX { ieee8023MacIndex }
 ::= { ieee8023MacTable 1 }

Ieee8023MacEntry ::= SEQUENCE {
    ieee8023MacIndex
 INTEGER,
    ieee8023MacTransmitted
 Counter,
    ieee8023MacNotTransmitted
 Counter,
    ieee8023MacDeferred
 Counter,
    ieee8023MacCollisions
 Counter,
    ieee8023MacSingleCollisions
 Counter,
    ieee8023MacMultipleCollisions
 Counter,
    ieee8023MacExcessCollisions
 Counter,
    ieee8023MacLateCollisions
 Counter,
    ieee8023MacCarrierLostErrors
 Counter,
    ieee8023MacNoHeartBeatErrors
 Counter,
    ieee8023MacFramesReceived
 Counter,
    ieee8023MacUndeliverableFramesReceived
 Counter,
    ieee8023MacCRCErrors
 Counter,
    ieee8023MacAlignmentErrors
 Counter,
    ieee8023MacResourceErrors
 Counter,
    ieee8023MacControlFieldErrors
 Counter,
    ieee8023MacUnknownProtocolErrors
 Counter,
    ieee8023MacMulticastsAccepted
 Counter
}

ieee8023MacIndex OBJECT-TYPE
 SYNTAX INTEGER
 ACCESS  read-only
 STATUS  mandatory
 DESCRIPTION
  "The index value that uniquely identifies the
  interface to which this entry is applicable.  The
  interface identified by a particular value of this
  index is the same interface as identified by the
  same value of ifIndex."
 ::= { ieee8023MacEntry 1 }

ieee8023MacTransmitted OBJECT-TYPE
 SYNTAX Counter
 ACCESS  read-only
 STATUS mandatory
 DESCRIPTION
  "The number of frames successfully transmitted."
 ::= { ieee8023MacEntry 2 }

ieee8023MacNotTransmitted OBJECT-TYPE
 SYNTAX Counter
 ACCESS  read-only
 STATUS mandatory
 DESCRIPTION
  "The number of frames not transmitted."
 ::= { ieee8023MacEntry 3 }

ieee8023MacDeferred OBJECT-TYPE
 SYNTAX Counter
 ACCESS  read-only
 STATUS mandatory
 DESCRIPTION
  "The number of frames deferred because the medium
  was busy."
 ::= { ieee8023MacEntry 4 }

ieee8023MacCollisions OBJECT-TYPE
 SYNTAX Counter
 ACCESS  read-only
 STATUS mandatory
 DESCRIPTION
  "Total number of transmit attempts that were
  retransmitted due to collisions.  SunOS with Intel 82586
  Ethernet driver - total number of collisions."
 ::= { ieee8023MacEntry 5 }

ieee8023MacSingleCollisions OBJECT-TYPE
 SYNTAX Counter
 ACCESS  read-only
 STATUS mandatory
 DESCRIPTION
  "Number of transmit attempts that are involved in a
  single collision and are subsequently transmitted
  successfully.  SunOS - this is always 0."
 ::= { ieee8023MacEntry 6 }

ieee8023MacMultipleCollisions OBJECT-TYPE
 SYNTAX Counter
 ACCESS  read-only
 STATUS mandatory
 DESCRIPTION
  "Number of transmit attempts that are involved in
  between 2 and 15 collision attempts and are
  subsequently transmitted successfully.  SunOS with Intel
  82586 is always 0.  SunOS with AMD 7990 LANCE driver -
  number of transmit attempts that are involved in between
  1 and 15 collision attempts and are subsequently
  transmitted successfully."
 ::= { ieee8023MacEntry 7 }

ieee8023MacExcessCollisions OBJECT-TYPE
 SYNTAX Counter
 ACCESS  read-only
 STATUS mandatory
 DESCRIPTION
  "Number of transmit attempts that are involved in
  more than 15 collision attempts and are subsequently
  transmitted successfully.  SunOS with Intel 82586
  Ethernet driver - this is always 0."
 ::= { ieee8023MacEntry 8 }

ieee8023MacLateCollisions OBJECT-TYPE
 SYNTAX Counter
 ACCESS  read-only
 STATUS mandatory
 DESCRIPTION
  "Number of transmit attempts aborted because a
  collision occurred after the allotted channel time
  had elapsed."
 ::= { ieee8023MacEntry 9 }

ieee8023MacCarrierLostErrors OBJECT-TYPE
 SYNTAX Counter
 ACCESS  read-only
 STATUS mandatory
 DESCRIPTION
  "Number of times that carrier sense was lost when
  attempting to transmit."
 ::= { ieee8023MacEntry 10 }

ieee8023MacNoHeartBeatErrors OBJECT-TYPE
 SYNTAX Counter
 ACCESS  read-only
 STATUS mandatory
 DESCRIPTION
  "Number of times no heart beat was indicated after a
  transmission."
 ::= { ieee8023MacEntry 11 }

ieee8023MacFramesReceived OBJECT-TYPE
 SYNTAX Counter
 ACCESS  read-only
 STATUS mandatory
 DESCRIPTION
  "Number of frames successfully received."
 ::= { ieee8023MacEntry 12 }

ieee8023MacUndeliverableFramesReceived OBJECT-TYPE
 SYNTAX Counter
 ACCESS  read-only
 STATUS mandatory
 DESCRIPTION
  "Number of frames received that were not delivered
  because the software buffer was overrun when frames
  were sent faster than they could be received."
 ::= { ieee8023MacEntry 13 }

ieee8023MacCRCErrors OBJECT-TYPE
 SYNTAX Counter
 ACCESS  read-only
 STATUS mandatory
 DESCRIPTION
  "Number of Cyclical Redundancy Check (CRC) errors
  detected."
 ::= { ieee8023MacEntry 14 }

ieee8023MacAlignmentErrors OBJECT-TYPE
 SYNTAX Counter
 ACCESS  read-only
 STATUS mandatory
 DESCRIPTION
         "Number of frames received that were both misaligned
  and had bad CRC."
 ::= { ieee8023MacEntry 15 }

ieee8023MacResourceErrors OBJECT-TYPE
 SYNTAX Counter
 ACCESS  read-only
 STATUS mandatory
 DESCRIPTION
  "Number of frames received that were lost due to lack
  of resources."
 ::= { ieee8023MacEntry 16 }

ieee8023MacControlFieldErrors OBJECT-TYPE
 SYNTAX Counter
 ACCESS  read-only
 STATUS mandatory
 DESCRIPTION
  "Number of frames received with errors in the control
  field.  SunOS - this is always 0."
 ::= { ieee8023MacEntry 17 }

ieee8023MacUnknownProtocolErrors OBJECT-TYPE
 SYNTAX Counter
 ACCESS  read-only
 STATUS mandatory
 DESCRIPTION
  "Number of frames dropped because the type field
  or sap field referenced an invalid protocol.  SunOS -
  this is always 0."
 ::= { ieee8023MacEntry 18 }

ieee8023MacMulticastsAccepted OBJECT-TYPE
 SYNTAX Counter
 ACCESS  read-only
 STATUS mandatory
 DESCRIPTION
  "Number of accepted muliticast addresses."
 ::= { ieee8023MacEntry 19 }

-- The Icmp Group

icmpEchoReq OBJECT-TYPE
 SYNTAX INTEGER
 ACCESS  read-only
 STATUS mandatory
 DESCRIPTION
  "The number of milliseconds it takes for an ICMP
  echo request to respond.  IcmpEchoReq is
      -1 if there is an internal error,
      -2 if the echo request timed out,
      -3 if the echo reply is not the correct reply,
      -4 if the packet size is too large, and
      -5 if the timeout is invalid.

  To request the ICMP response time for IP address
  a1.a2.a3.a4 with a timeout of t and a packet size of s,
  send a request for icmpEchoReq.s.t.a1.a2.a3.a4.

  For example, suppose one wanted to find out the number
  of milliseconds it took to ping 15.2.112.113, with time
  out of 8 seconds, and packet size of 75.  Accordingly,
  icmpEchoReq.75.8.15.2.112.113 would identify the number
  of milliseconds.

  This MIB object is there only to provide for backward
  compatibility. A new MIB object is provided which does not
  violate the SNMP standards too,
  'icmp.icmpEchoReqTable.icmpEchoReqEntry.icmpEchoReqTime'.
  This new MIB object is recommended to be used to achieve the
  same funtionality as provided by this (icmp.icmpEchoReq)
  MIB object."
 ::= { icmp 1 }

icmpEchoReqTable OBJECT-TYPE
    SYNTAX  SEQUENCE OF IcmpEchoReqEntry
    ACCESS  not-accessible
    STATUS  mandatory
    DESCRIPTION
        "A conceptual table holding the ICMP response times for
        various remote hosts. The table is a conceptual one in the
        sense that, the table actually contains no data. When a query
        for the table object icmpEchoReqTime is received by the agent
        an ICMP echo request is sent to the remote host, the ICMP
        echo reply is received, the elapsed time is calculated and
        is sent back as the response. Note that except the columnar
        object icmpEchoReqTime other objects in the table, viz.,
        icmpEchoReqPktSize, icmpEchoReqTimeout and icmpEchoReqHost,
        have ACCESS previlege as not-accessible, those variables
        cannot be queried for.

        The table entries have the objects icmpEchoReqPktSize,
        icmpEchoReqTimeout and icmpEchoReqHost as the indices, which
        is effectively a way of transfering these required details
        to the agent, so that the agent could do its function and
        respond appropriately."
    ::= { icmp 2 }

icmpEchoReqEntry OBJECT-TYPE
    SYNTAX  IcmpEchoReqEntry
    ACCESS  not-accessible
    STATUS  mandatory
    DESCRIPTION
        "Each entry in the table icmpEchoReqTable is a conceptual one.
        See description of icmpEchoReqTable for more details."
    INDEX { icmpEchoReqPktSize, icmpEchoReqTimeOut, icmpEchoReqHost }
    ::= { icmpEchoReqTable 1 }

IcmpEchoReqEntry ::=
    SEQUENCE {
        icmpEchoReqTime
            INTEGER,
        icmpEchoReqPktSize
            INTEGER,
        icmpEchoReqTimeOut
            INTEGER,
        icmpEchoReqHost
            IpAddress
    }

icmpEchoReqTime OBJECT-TYPE
    SYNTAX  INTEGER
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
        "The elapsed time between the time the ICMP echo request is
        sent to the host identified by the index object icmpEchoReqHost
        and the time the ICMP echo reply is received at the agent host.
        The ICMP packet size and the time out to be used for the
        ICMP echo request are identified by the indices
        icmpEchoReqPktSize and icmpEchoReqTimeOut. See description
        of icmpEchoReqTable for more details.

        In other words, the number of milliseconds it takes for
        an ICMP echo request to respond. Other return values:
            -1 if there is an internal error,
            -2 if the echo request timed out,
            -3 if the echo reply is not the correct reply,
            -4 if the packet size is too large, and
            -5 if the timeout is invalid.

        To request the ICMP response time for IP address
        a1.a2.a3.a4 with a timeout of t and a packet size of s,
        send a request for icmpEchoReqTime.s.t.a1.a2.a3.a4.

        For example, suppose one wanted to find out the number
        of milliseconds it took to ping 15.2.112.113, with time
        out of 8 seconds, and packet size of 75.  Accordingly,
        icmpEchoReqTime.75.8.15.2.112.113 would identify the
        number of milliseconds."
    ::= { icmpEchoReqEntry 1 }

icmpEchoReqPktSize OBJECT-TYPE
    SYNTAX  INTEGER
    ACCESS  not-accessible
    STATUS  mandatory
    DESCRIPTION
        "The packet size to be used for the ICMP echo request, see
        description of icmpEchoReqTable for more details.

        The object serves as the first index out of three indices
        used when the object icmpEchoReqTime is queried. Note that
        this object's value cannot be queried for, this object serves
        as an input to the agent itself and a query for this object
        makes no sense."
    ::= { icmpEchoReqEntry 2 }

icmpEchoReqTimeOut OBJECT-TYPE
    SYNTAX  INTEGER
    ACCESS  not-accessible
    STATUS  mandatory
    DESCRIPTION
        "The time period in seconds to wait for an ICMP echo reply
        message after an ICMP echo request is sent to the identified
        host, see description of icmpEchoReqTable for more details.

        The object serves as the second index out of three indices
        used when the object icmpEchoReqTime is queried. Note that
        this object's value cannot be queried for, this object serves
        as an input to the agent itself and a query for this object
        makes no sense."
    ::= { icmpEchoReqEntry 3 }

icmpEchoReqHost OBJECT-TYPE
    SYNTAX  IpAddress
    ACCESS  not-accessible
    STATUS  mandatory
    DESCRIPTION
        "The host to which the ICMP echo request is to be sent,
        the ping time between the host identified by this index
        object and the agent's host is what is queried for, see
        description of icmpEchoReqTable for more details.

        The object serves as the last index out of three indices
        used when the object icmpEchoReqTime is queried. Note that
        this object's value cannot be queried for, this object serves
        as an input to the agent itself and a query for this object
        makes no sense."
    ::= { icmpEchoReqEntry 4 }

-- The Trap Group

trapDestinationNum OBJECT-TYPE
 SYNTAX Gauge
 ACCESS  read-only
 STATUS mandatory
 DESCRIPTION
  "The number of trap destinations."
 ::= { trap 1 }

-- The Trap Destination Table

trapDestinationTable OBJECT-TYPE
 SYNTAX SEQUENCE OF TrapDestinationEntry
 ACCESS  not-accessible
 STATUS mandatory
 DESCRIPTION
  "List of addresses to which the agent sends traps."
 ::= { trap 2 }

trapDestinationEntry OBJECT-TYPE
 SYNTAX TrapDestinationEntry
 ACCESS  not-accessible
 STATUS mandatory
 DESCRIPTION
  "Each entry contains the address of a management
  station."
 INDEX { trapDestination }
 ::= { trapDestinationTable 1 }

TrapDestinationEntry ::= SEQUENCE {
    trapDestination
 IpAddress
}

trapDestination OBJECT-TYPE
 SYNTAX IpAddress
 ACCESS  read-write
 STATUS mandatory
 DESCRIPTION
  "Address to which the agent sends traps."
     ::= { trapDestinationEntry 1 }

-- The SnmpdConf Group

snmpdConfRespond OBJECT-TYPE
 SYNTAX INTEGER {
      true(1),
      false(2)
  }
 ACCESS  read-write
 STATUS mandatory
 DESCRIPTION
  "The SNMP agent was configured to respond to all
  objects if snmpdConfRespond is true.  HP-Internal
  use only."
 ::= { snmpdConf 1 }

snmpdReConfigure OBJECT-TYPE
 SYNTAX INTEGER {
      reset(1)
  }
 ACCESS  read-write
 STATUS mandatory
 DESCRIPTION
  "The agent will re-configure itself if
  snmpdReConfigure is set to reset(1)"
 ::= { snmpdConf 2 }

snmpdFlag OBJECT-TYPE
 SYNTAX INTEGER {
      removetrap(1),
      netwareproxy(2)
  }
 ACCESS  read-only
 STATUS mandatory
 DESCRIPTION
  "Indicates the capability of the agent."
 ::= { snmpdConf 3 }

snmpdLogMask OBJECT-TYPE
 SYNTAX INTEGER
 ACCESS  read-write
 STATUS mandatory
 DESCRIPTION
  "The agent's log mask."
 ::= { snmpdConf 4 }

snmpdVersion OBJECT-TYPE
 SYNTAX INTEGER
 ACCESS  read-only
 STATUS mandatory
 DESCRIPTION
  "The agent's version number."
 ::= { snmpdConf 5 }

snmpdStatus OBJECT-TYPE
 SYNTAX INTEGER {
      up(1),
      down(2)
  }
 ACCESS  read-write
 STATUS mandatory
 DESCRIPTION
  "Indicates the status of the agent.  Setting
  the agent to down will kill it."
 ::= { snmpdConf 6 }

snmpdSize OBJECT-TYPE
 SYNTAX INTEGER
 ACCESS  read-only
 STATUS mandatory
 DESCRIPTION
  "The amount of memory the agent has allocated."
 ::= { snmpdConf 7 }

snmpdWhatString OBJECT-TYPE
 SYNTAX DisplayString
 ACCESS  read-only
 STATUS mandatory
 DESCRIPTION
  "The what string of the agent."
 ::= { snmpdConf 9 }

-- The Cluster Group
--
--  This group is not implemented on SunOS/Solaris.

isClustered OBJECT-TYPE
 SYNTAX INTEGER {
  standalone(1),
  rootserver(2),
  cnode(3)
     }
 ACCESS read-only
 STATUS mandatory
 DESCRIPTION
  "Describes whether machine is clustered or not."
 ::= { cluster 1 }

clusterTable OBJECT-TYPE
 SYNTAX SEQUENCE OF ClusterEntry
 ACCESS not-accessible
 STATUS mandatory
 DESCRIPTION
  "List of nodes on the cluster."
 ::= { cluster 2 }

clusterEntry OBJECT-TYPE
 SYNTAX ClusterEntry
 ACCESS not-accessible
 STATUS mandatory
 DESCRIPTION
  "Each entry contains information about the clustered
  node."
 INDEX {clusterID }
 ::= { clusterTable 1 }

ClusterEntry ::= SEQUENCE {
    clusterID
 INTEGER,
    clusterMachineID
 OCTET STRING,
    clusterType
 DisplayString,
    clusterCnodeName
 DisplayString,
    clusterSwapServingCnode
 INTEGER,
    clusterKcsp
 INTEGER,
    clusterCnodeAddress
 IpAddress
}

clusterID OBJECT-TYPE
 SYNTAX INTEGER
 ACCESS  read-only
 STATUS mandatory
 DESCRIPTION
  "The cnode id."
     ::= { clusterEntry 1 }

clusterMachineID OBJECT-TYPE
 SYNTAX OCTET STRING
 ACCESS  read-only
 STATUS mandatory
 DESCRIPTION
  "The cnode machine id."
     ::= { clusterEntry 2 }

clusterType OBJECT-TYPE
 SYNTAX DisplayString
 ACCESS  read-only
 STATUS mandatory
 DESCRIPTION
  "The cnode type (r or c)."
     ::= { clusterEntry 3 }

clusterCnodeName OBJECT-TYPE
 SYNTAX DisplayString
 ACCESS  read-only
 STATUS mandatory
 DESCRIPTION
  "The cnode name."
     ::= { clusterEntry 4 }

clusterSwapServingCnode OBJECT-TYPE
 SYNTAX INTEGER
 ACCESS  read-only
 STATUS mandatory
 DESCRIPTION
  "The swap serving cnode."
     ::= { clusterEntry 5 }

clusterKcsp OBJECT-TYPE
 SYNTAX INTEGER
 ACCESS  read-only
 STATUS mandatory
 DESCRIPTION
  "KCSP."
     ::= { clusterEntry 6 }

clusterCnodeAddress OBJECT-TYPE
 SYNTAX IpAddress
 ACCESS  read-only
 STATUS mandatory
 DESCRIPTION
  "The cnode IP Address."
     ::= { clusterEntry 7 }

clusterCnodeID OBJECT-TYPE
 SYNTAX INTEGER
 ACCESS  read-only
 STATUS mandatory
 DESCRIPTION
  "The machine's cnodes id"
     ::= { cluster 3 }

-- The AuthFail Group

authFailTable OBJECT-TYPE
 SYNTAX SEQUENCE OF AuthFailEntry
 ACCESS  not-accessible
 STATUS mandatory
 DESCRIPTION
  "List of managers that caused an authentication failure.
  This list has a maximum size."
 ::= { authfail 1 }

authFailEntry OBJECT-TYPE
 SYNTAX AuthFailEntry
 ACCESS  not-accessible
 STATUS mandatory
 DESCRIPTION
  "Each entry contains the ip address of the management
  station."
 INDEX { authIpAddress }
 ::= { authFailTable 1 }

AuthFailEntry ::= SEQUENCE {
    authIpAddress
 NetworkAddress,
    authTime
 TimeTicks,
    authCommunityName
 OCTET STRING
}

authIpAddress OBJECT-TYPE
 SYNTAX NetworkAddress
 ACCESS  read-only
 STATUS mandatory
 DESCRIPTION
  "The ip address of the management station that sent a
  request to the agent with an incorrect community name."
     ::= { authFailEntry 1 }

authTime OBJECT-TYPE
 SYNTAX TimeTicks
 ACCESS  read-only
 STATUS mandatory
 DESCRIPTION
  "The time since the agent received the un-authenticated
  request."
     ::= { authFailEntry 2 }

authCommunityName OBJECT-TYPE
 SYNTAX OCTET STRING
 ACCESS  read-only
 STATUS mandatory
 DESCRIPTION
  "The community name used in the request"
     ::= { authFailEntry 3 }

-- the OpenView trap variables Group
-- These object ID's cannot be retrieved from the SNMP Agent, but
--  instead document the objects sent with OpenView SNMP traps
 
openViewSourceId OBJECT-TYPE
 SYNTAX INTEGER
 ACCESS not-accessible
 STATUS mandatory
 DESCRIPTION
  "The identifier of the software generating the trap/event.
   This number is used by HP OpenView software when it sends
   an event to the OpenView event system.  It identifies
   which software component sent the event.
  
   This object cannot be retrieved from the SNMP agent."
 ::= { openViewTrapVars 1 }

openViewSourceName OBJECT-TYPE
 SYNTAX OCTET STRING
 ACCESS not-accessible
 STATUS mandatory
 DESCRIPTION
  "The source of the event (may not be the machine upon
   which the event was generated).  This string is used
   by HP OpenView software when it sends an event.  It
   identifies for which source (node) the event is generated.

   This object cannot be retrieved from the SNMP agent."
 ::= { openViewTrapVars 2 }

openViewObjectId OBJECT-TYPE
 SYNTAX OCTET STRING
 ACCESS not-accessible
 STATUS mandatory
 DESCRIPTION
  "The OpenView object identifier associated with the
   source of the trap/event.

   This object cannot be retrieved from the SNMP agent."
 ::= { openViewTrapVars 3 }

openViewData OBJECT-TYPE
 SYNTAX OCTET STRING
 ACCESS not-accessible
 STATUS mandatory
 DESCRIPTION
  "Any miscellaneous data sent with an OpenView trap/event.

   This object cannot be retrieved from the SNMP agent."
 ::= { openViewTrapVars 4 }

openViewSeverity OBJECT-TYPE
 SYNTAX OCTET STRING
 ACCESS not-accessible
 STATUS mandatory
 DESCRIPTION
  "The OpenView event severity associated with the trap/event.

   This object cannot be retrieved from the SNMP agent."
 ::= { openViewTrapVars 5 }

openViewCategory OBJECT-TYPE
 SYNTAX OCTET STRING
 ACCESS not-accessible
 STATUS mandatory
 DESCRIPTION
  "The OpenView event category associated with the trap/event.

   This object cannot be retrieved from the SNMP agent."
 ::= { openViewTrapVars 6 }

openViewFilter OBJECT-TYPE
 SYNTAX OCTET STRING
 ACCESS not-accessible
 STATUS mandatory
 DESCRIPTION
  "The event filter for an application connecting to the
   OpenView event system.

   This object cannot be retrieved from the SNMP agent."
 ::= { openViewTrapVars 7 }

openViewEntity OBJECT-TYPE
 SYNTAX OCTET STRING
 ACCESS not-accessible
 STATUS mandatory
 DESCRIPTION
  "The entity (string name) of an application connecting
   to the OpenView event system.

   This object cannot be retrieved from the SNMP agent."
 ::= { openViewTrapVars 8 }

openViewAddress OBJECT-TYPE
 SYNTAX OCTET STRING
 ACCESS not-accessible
 STATUS mandatory
 DESCRIPTION
  "The IP address of the node from where an application
   is connecting to the OpenView event system.

   This object cannot be retrieved from the SNMP agent."
 ::= { openViewTrapVars 9 }

openViewPid OBJECT-TYPE
 SYNTAX OCTET STRING
 ACCESS not-accessible
 STATUS mandatory
 DESCRIPTION
  "The process ID of an application connecting to the
   OpenView event system.

   This object cannot be retrieved from the SNMP agent."
 ::= { openViewTrapVars 10 }

END